post01

a boiler drives steam at 10 mpa and 550c to a steam turbine after first stage 25 of the steam is extracted at 1 4 mpa for a proc

Purchased equipment: a boiler drives steam at 10 mpa and 550c to a steam turbine after first stage 25 of the steam is extracted at 1 4 mpa for a proc
Location: WUXI China
Telephone: +86 13861509127
E-mail: [email protected]
Contact us for more details about our boilers, solutions and services.

High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ and reduce heat lost.Sufficient steam storage room and heating area to generate high quality steam and high thermal power.Condenser is added to recycle the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce flue gas emission temperature and increase the thermal efficiency over 98% and save operating cost.

Environmental protection

Big combustion chamber equipped with Low emission combustion burner effectively reduce the NOx to 30mg/m3. Smoke duct and smoke outlet use internal insulation to reduce operating noise.

Combustion chamber uses full membrane water cooling wall structure and pressurized combustion without smoke mixture.

Energy conservation

Good quality alumina silicate fiber and fire clay insulation material are used and the boiler body temperature is controlled below 45℃ and greatly heat loss is reduced. Combustion chamber is designed with narrow distance tube membrane water cooling wall which has good air proof to reduce heat lost and increase boiler thermal efficiency. Internal inspection holes uses high-alumina refractory and manhole cover seal devices, solving superheat problem in this part caused by using refractory bricks.

CNC manufacturing technology

The key processing technologies such as steel plate blanking, circling, drum and tube plate drilling adopt advanced CNC machining to reduce the assembly stress and prolong the service life of the boiler.

Steel tube cutting, thread tube pressing and convection tube processing all adopt advanced CNC technology.

Automatic production line.

Leave a Comment

pro_first

The Handbook of Advanced Materials: Enabling New Design

4.41 4.12 3.92 1.90 2.10 3.73 4.41 4.83 4.90 3.82 3.33 4.40 3.50 3.53 Fracture Toughness MPa.m1/2 35 30 25 20 15 10 5 Typical Ceramics FIGURE 2.3 Cast Iron WC-Co Cermet Steel Although the initial driver for silicon nitride development was gas turbine engine components, the first major application was cutting tool inserts [9]. Cutting

Steam cycle - Revol

Steam cycle Save The Rankine cycle is a model that is used to predict the performance of steam turbine systems, though the theoretical principle also applies to reciprocating engines such as steam locomotives.

Gasification for Practical Applications | Gasification | Co

10 Gasification for Practical Applications. Item. Top-feeding. Activation energies of gasification reactions with CO2 and steam. 10. a) 10 = 0.75 = 0.50. with and without catalyst The phenomena of coke-matrix state and controlling process in the lump 4.1. Introduction 4.1.1. The strength after gasification reaction and the spatial

LEARN NETWORK ADVANCE - PDF - docplayer.n

39th Annual Meeting Exhibition February 4-8, 200 Washington State Convention Trade Center Seattle, Washington USA Going for the Gold in Materials Technology Includes: Meeting Information Floor Plans A dense pure NbC hard material with a relative density of up to 98% was produced with simultaneous application of 80 MPa pressure within 2

final program - PDF Free Download - zdoc.si

Engineering and Applied Science in Computer Science, in 1989 and BS degree from Cornell . He received his BS and MS degrees in Biomedical .. ID: 10048.

What Are Supercritical CO2 Power Cycles? - powermag.c

CO 2 has a relatively low critical pressure of 7.4 megapascals (mPA) in a conventional boiler); energy is extracted from the CO 2 as it which consists of a 1-MWe turbine (with a 10-MWe

Online performance monitoring platform based on the whol

the exhaust steam of HPC, the reheated steam, the extracted steam from IPC/LPC, the exhaust steam of LPC, the feed water entering the economizer, the feedwater leaving the economizer, the steam leav-

Analysis of a novel solar electricity generation syste

The SEGS developed in the DISS project had steam temperature of 673 K and pressure of 10 MPa at the turbine inlet , . There was a degree of superheat of about 90 K. The plant developed in INDITEP project (the logical continuation of the DISS project) had steam temperature of 673 K and pressure of 6.5 MPa at the turbine inlet .

Estimation of condensate mass flow rate during purgin

Estimation of condensate mass flow rate during purging time in heat recovery steam generator of combined cycle power plant. electric motor driven and one 1 steam turbine driven)

GB2086744A - Method for producing steam from the liquid a

Method for producing steam from the liquid an a moist gas stream Download PDF Info Publication number GB2086744A. boiler heat Prior art date 1980-10-30 Legal status (The legal status is an assumption and is not a legal conclusion. Google has not performed a legal analysis and makes no representation as to the accuracy of the status listed.)

Frederick J. Barclay-Combined Power and Process_ - A

The losses involved in mixing enable complete combustion to be obtained compactly and are.960 8.288.an Exergy Approach Table 3.to(s .h.690 Table 3.76693air Burn steam/fuel/0.9-288. therefore.6 = 2473. For the future.040-6.04/1.11 Table 3.76693air Expand products + cooling air compression blade cooling EHRB heat transfer Steam turbine.4/3.4 In (1.